有没有高手帮忙读一下西门子840D磨床程序
%_N_SCHEIB1_SPF
;$PATH=/_N_SPF_DIR
;Dateiinfo("TYROLIT 50A 601 K 5A V217")
;Kennung(2.02/32 (c) J.H., 02.12.2005)
;Datum(10/28/13)
;Vorspann_Anfang()
R989=0
IF R988-1 > R989 GOTOF MARKE
;Vorspann_Ende()
Kommentar="";
R499=210;
R498=249;
R497=0;
R496=1;
R495=0;
R465=1;
R466=1;
R440=0;
R480=0.0000;
R482=0.0000;
R481=0.0000;
R483=0.0000;
R484=0.0000;
R485=0.0000;
R486=0.0000;
R487=0.0000;
R488=0;
R490=0;
R491=0.0000;
R492=0.0000;
R493=0.0000;
R408=0.0000;
R494=0.0;
R110=0;
R113=0.0;
;Befehl(IF_0)
IF R467==1 GOTOF GEOM
R400=1;
R401=2;
R405=24.0;
R406=0.0000;
R412=630.0000;
R454=0.0020;
R431=0.0300;
R432=0.0000;
R433=0.0000;
R434=0.0000;
R435=0.0000;
R436=0.0000;
R437=0.0000;
R438=0.0000;
R439=0.0000;
R457=0.0000;
R441=0.0109;
R442=0.0000;
R443=0.0000;
R444=0.0000;
R445=0.0000;
R446=0.0000;
R447=0.0000;
R448=0.0000;
R449=0.0000;
;Befehl(M_GEOM)
GEOM:
R047=1;
R410=-150.0560;
R411=0.0000;
R409=0.0000;
R430=0.0000;
R450=0.0000;
;Befehl(UP_2)
CALL "/_N_CUS_DIR/_N_L912_SPF"
;Befehl(UP_ANT)
DUMMY_MARKE:
;Befehl(M_START)
BEGINNE:
;Befehl(PROF_1)
IF ((R981==1) AND (R490 == 0))
;Befehl(PROF_2)
IF ((R430<=0) AND (R409<=0) AND (R450<=0)) GOTOF PROFENDE
;Befehl(PROF_3)
TRANS X=R245 Z=R248
;Befehl(PROF_4)
ENDIF
;Befehl(UP_ANT_D)
DUMMY_MARKE:
;DIN_Programm_Anfang(DIN)
;EISENBAHNACHSE / RE 2B
;XWP=-150.056 , ZWP=0
M1=61
N10 G0 G90 G500
N11 Z=-230
;START
N12 M2=8 M1=8
N13 X=-148
N20 G01 X=-150.052 Z=-230 F=200 ;P1
N21 G64 G01 X=-150.076 Z=-25.62 ;P2
N30 G64 G02 X=-168.000 Z=-0.770 CR=40.7 F=180 ;P3
N40 G64 G02 X=-170.060 Z=0 CR=2.3 ;P4
N50 G64 G01 X=-180.084 Z=0 F=200 ;P5
N60 G64 G01 X=-180.086 Z=57.336 F=200 ;P6
N70 G64 G02 X=-216.870 Z=85.000 CR=30.7 F=190 ;P7
N80 G64 G01 X=-240.000 Z=85.000 F=180 ;P8
N90 G64 G00 X=-240.000 Z=90
;P9
N91 G64 G00 X=-100.000 Z=90 ;P10
;END
N94 M1=9 M2=9
;DIN_Programm_Ende()
;Befehl(UP_3)
CALL "/_N_CUS_DIR/_N_L914_SPF"
;Befehl(RUECK)
IF R401 > 0 GOTOB BEGINNE
;Befehl(PROF_5)
PROFENDE:
CALL "/_N_CUS_DIR/_N_L915_SPF";
;Zwischen_Anfang()
M17
MARKE:
R989=R989+1
IF R988-1 > R989 GOTOF MARKE
;Zwischen_Ende()
N1 WORK_1:
;Nachspann_Anfang()
MARKE:
MSG ("Konturnummer " << R988 << " nicht vorhanden !!!")
ENDE:
;Nachspann_Ende()
M17
